Cleaning Your Concept2 Rower

by May 22, 2020The Machine

Maintenance on your Concept2 rowing machine is one of those things that’s easy to forget but is well worth your time. It doesn’t take long, and will greatly increase the life of your machine. Concept2 really did us all a favor with how easy it is to maintain these machines. It’s much easier than you may think. 

Concept2 model C, D, and E machines are all very similar in the maintenance they require. If there are any differences between the models, I will mention it in the following sections. 

In this article, I am focusing on maintenance, not diagnosing problems with your rower. This maintenance is what you need to do even if your machine is in perfect working condition. Doing these things will keep it running that way!

AFTER EACH USE

Every time your rower is used, it should be wiped down. This may seem excessive, but getting into this habit early on is worth it. 

The seat and the handle see the most grime from us, so use a disinfectant cleaner on those. You can mix ¼ cup of bleach in a gallon of water and put that into a spray bottle or use a store-bought version if you’re averse to bleach. You can spray these parts directly, and wipe off with a cloth. The screen and buttons also need to be wiped down but don’t spray the electronics directly. Spray the cloth first, and then wipe down the screen. 

The monorail also needs to see some love. This part of the machine is easy to forget, and often the part I see the dirtiest. Clean the monorail with a cloth, and you can use water with soap or any glass cleaner. Do NOT use your bleach solution or abrasive cleaner on the monorail. 

In general, it’s good to wipe down the whole machine with your cloth after each use. Try to get as much dust off around the wheel, but don’t forget those foot stretchers too every so often. 

This frequent maintenance will keep your machine looking sharp, whether that’s in your garage or in your gym.

shows how to clean the rowing machine

PERIODIC MAINTENANCE

Cleaning your rower after each use is well worth it, but there’s more. 

There are two main things to remember to do every so often with your rower, and that’s oiling the chain and cleaning the flywheel. 

Concept2 recommends oiling the chain after 50 hours of use. For gyms where the rower is used often, that could be weekly or every other week depending on the usage. For home gyms, that would be closer to monthly if you use the rower every day, or every 3 months if you use it periodically. 

Standard 3-in-1 oil that you can get at pretty much any hardware store (Lowe’s, Home Depot, Amazon, etc) will do. You will also need a friend for this as well. Do NOT use cleaners like WD-40. 

One person will take the handle and back up until as much of the chain is out as possible. Then the other person put some oil on a paper towel and wipe down the chain. Make sure to wipe off any excess. Once this is done, have one person take a couple of strokes on the machine so the oil can be distributed into all the nooks and crannies of the chain. 

oiling indoor rowing chain

Cleaning the flywheel is up next. You’ll want to check for dust at least a couple of times a year. For some that might be every 3 months, and for others every 6 months. It really depends on how often you use your machine. If you own a gym where the rowers are used often, you may need to check for dust monthly. 

Getting rid of the dust inside of the flywheel will help the rower to function more properly. When there is dust in the flywheel, there is less air. This means that with more dust, you’ll need to increase the airflow to get the same drag. You’ll find that you have to put your drag setting on the flywheel higher and higher to achieve the same resistance. 

Model C rowing machines have a slightly different design to remove the flywheel than the Model D and E rowing machines. The pictures below are of a Model C rowing machine. For better instructions on how to clean a model D and E rowing machine, see this video

  1. Loosen each screw around the housing. Go back around and remove each screw.
  2. Remove the outer panel to see the flywheel.
  3. Use a vacuum to get the dust out, or use a cloth and wipe it out. 
  4. Put the outer panel back on.
  5. Tighten the bolts uniformly as you go around. 

You may be surprised to find that you can now put your drag setting lower in order the achieve the same resistance (or drag factor) you were before cleaning your machine.

How to Use Force Curves to Fix Technique

How to Use Force Curves to Fix Technique

You may know what a force curve is, and you might not. There’s no rule anywhere saying you need to know what your force curve looks like, or use it. However, it can be a useful tool to see how you’re applying power.  Confused? No worries. We will get into what a force...

Everything to Know About the Catch Position

Everything to Know About the Catch Position

 There’s a lot that goes into having a good catch position on the rowing machine.  A good catch allows you to start your stroke off right and sets you up for success each and every stroke you take.  Here is a picture of a good catch position: Here are the big things...

Single-Leg Rowing Drill

Single-Leg Rowing Drill

This drill for indoor rowing is just as the name implies. You take one foot out of the foot stretchers and only row with one leg. The leg that isn’t rowing hangs out on the side while you row.  I don’t recommend trying this one in a boat at all. There’s really no...